Imperial Suspension Part Numbers


Imperial Home Page -> Parts -> Suspension -> Part Numbers


Read the 1953 - 1961 Chrysler and Imperial parts manual which includes the numbers for the front suspension and rear suspension parts for these models.

 

Read the 1967 front suspension part number sheets.

 

CHASSIS

NAPA

BALL JOINTS

CONTROL ARM BUSHINGS
Year Upper Lower Year Upper Lower
1954-56          
1957-59 260-1048 260-1084 1957-58   267-3174
1960-66

"

260-1418 threaded 1959-66 267-1171

"

1967-75

"

260-1084 1967-73 267-1288 267-5273
1974-75 267-1316 2673318      

 

TIE ROD ENDS


Year Outer Inner
1941 - 1948 269-2007 269-2008
1964 - 1973 269-2147 269-2148
1974 - 1975 269-2168 269-2171


CHASSIS

MOOG

BALL JOINTS CONTROL ARM BUSHINGS
Year Upper Lower Year Upper Lower
1957 - 1959 K778 K713 1957 - 1958 K319  
1960 - 1970 K714 K727 1959 - 1966 K325 K7025
1967 - 1970          

 

 

1960 - 1966 Shaft Kit  

K7028


Year Idler Arm Idler Arm Bracket/Bushing Pitman Am
1955 - 1956 K189  
1957 - 1958 K788  
1963 - 1966 *K7009 K7017
1967 - 1968 K7014 K7024
1969 - 1970 K7046

"

 



Year Inner Tie Rod Outr Tie Rod Center Link Adj. Sleeves
1949 - 1954 ES 166L ES 166R    
1955 - 1966 ES 570

"

ES 572 ES500S


 

 


SHOCK ABSORBERS 

Napa

 

Year Front Rear
1954 - 1946    
1957 - 1958    
1959 - 1964    
1965 - 1966 94050  
1967 - 1969 LH100009* 94053
1970 - 1973

"

94023
1974 - 1978 94015 94053
1981 - 1983

* "

94016


NOTE: 1981-83 cars listed w/o alc or air ride.
NOTE: It is usually possible to find a replacement shock if the mounting style at each end and the extended and collapsed lengths are known. Most shock catalogs have a buyer's guide that will enable the parts store to find a replacement with the necessary mounting and length requirements. Often the length will vary by a small amount, it is up to the owner to determine if the difference will cause any difficulties in the fully extended or compressed position.
Consult a KONI or KYB catalog to see if thtey list a shock for the application or by dimension and mounting style.
_________________________________________________________________________________________


WHEEL BEARINGS - SEALS - U JOINTS 

Napa - Timken

 


FRONT WHEEL SETS

Year Front Outer Front Inner Seal
1949 - 1956 09067&09195 15123 & 15245 49746
1957 - 1962 Set 2 Set 6

"

1963 - 1972

"

"

47366
1973 - 1976 Set 16 Set 11 47523
1973     47525
1974 - 1978      



REAR WHEEL SETS

Year Axle Bearing Inner Seal Outer Seal
1959 - 1964 25877 25821 46112
1960 - 1962 46292 47367  
1963 - 1964 46112    
1965 - 1973 Set 7 Right Side A7RK A7LK Left Side
1974 - 1975 6408 46482 46452


 

 

 


NOTES ABOUT THESE PART NUMBERS: Due to the fact that Chrysler no longer produces many of these parts and that Chrysler part numbers are quite often superseded or not in the Chrysler parts system any longer, aftermarket numbers are used. If enough current and correct Chrysler numbers are available, they can be added for what is still available from Chrysler.

I have arbitrarily chosen NAPA parts for the aftermarket, simply because of the availability of NAPA outlets and the fact that I have previously worked in their parts system. This IS NOT an expressed or implied advertisement or endorsement to use these products. MOST PARTS OUTLETS CAN INTERCHANGE THESE NUMBERS IF YOU DO NOT HAVE A LOCAL NAPA OR PREFER NOT TO PURCHASE FROM THEM.

IMPORTANT: ALL THESE REFERENCES HAVE BEEN ONLY SEARCHED FOR IMPERIAL OR NYB AS APPLICABLE. WHEN RESEARCHING THESE PART NUMBERS I SEARCHED FOR IMPERIAL, MODEL YEAR, ENGINE SIZE AND ANY OTHER NECESSARY DATA PERTINENT FOR THAT PARTICULAR PART.

FOR EACH GROUP OF PARTS THE SOURCE AND BRAND WILL BE LISTED< AS WELL AS ANY IMPORTANCE OF THE PART NUMBERS USED. IN THE CASE OF REBUILDABLE PARTS OR PARTS NOT EXPRESSLY NAPA- NOTES WILL INDICATE THE USE OF SUCH NUMBERS AND SOURCE.

Now when some uninterested, uncaring and uninformed counterman says " they didn't make that in that year......" or " its not listed...." you will have the upper-hand.

NOTES ON REBUILDABLE PARTS:  Many times a part is not available because the rebuilder has no "cores" from which to remanufacture a part from. It is usually possible and sometimes cheaper to send your part in - if you can be without the vehicle for the time required. Most of these parts are rebuilt by major suppliers to parts stores, regardless of the individual outlet. ( It is not uncommon for competing retail stores to be supplied by the same rebuilder) Some parts require the services of smaller specialized rebuilders, especially for vintage or very rare applications...


The following is a non inclusive list of many of the parts that can be easily rebuilt today:
Alternators, Generators, Starters, Water Pumps, Power Brake Boosters, Carburetors, Distributors, Brake Shoes, Master and Wheel Cylinders, Brake Calipers, Air Conditioning Compressors, Power Window Motors, Convertible Top Motors and Cylinders, Power Steering Pumps and Gearboxes, Wiper Motors, Motor and Trans Mounts., Fuel Pumps, Harmonic Balancers, Driveline Supports, Clutches and of course - Engines and Transmissions.


So if all else has failed, find a local or larger scale rebuilder either on your own or thru a parts store. DON'T SCRAP THE PART - if you have patience you can usually find someone to help.


This page was last updated July 31, 2003.  Send us your feedback, and come join the Imperial Mailing List - Online Car Club